Front wheel bearing grease cap
Front wheel bearing grease cap to fit all 750, 101 and 105 series cars.
Active filters
Front wheel bearing grease cap to fit all 750, 101 and 105 series cars.
Front wheel stub axle nut, left-hand thread. Fits all 750, 101 and 105 series cars.
Front wheel stub axle nut, right-hand thread. To suit all 105 series cars
OE-quality SKF front wheel bearing kit for 750, 101 and 105 series cars. Includes inner and outer bearings and an oil seal. Also suitable for 1900
Koni Classic front shock absorber for all 750 and 101 series cars. Ideal to match our Giulietta handling kit available under item code 750-095.
Standard front shock absorber for all 750 and 101 series cars.
Front lower wishbone bush to fit 101 series cars. Two required per side, four per car. Approximate internal diameter 21.9 mm.
Front upper wishbone bush to fit 101 series cars. Two required per side, four per car. Approximate internal diameter 18.8 mm.
Lower wishbone bush to fit 750 series cars. 2 per side, 4 in total per car. Approximate internal diameter 15.5 mm.
Front suspension upper wishbone bush for 750 series cars. 2 per side, 4 in total per car. Approximate internal diameter 13.9 mm.
Upper front suspension spacer for 750 and 101 series cars. Approximate sizes ID 14.5 mm, OD24 mm and 2 mm thick.
Lower front suspension spacer for 750 and 101 series cars. Approximate sizes ID 16 mm, OD30 mm and 2 mm thick.
Pair of rubber bushes for mounting the front anti-roll bar. They are intended for Alfa Romeo 750 and 101 series cars fitted with a 17 mm diameter bar.
A pair of front anti-roll bar mounting rubbers to fit early 750 series cars with a 15 mm bar.
Set of 4 rubber pads (2 used per side) for the front suspension control rods on all 750 and 101 series cars.
Front suspension control rod to fit all 750 and 101 series cars. Now includes a pair of rubber bushes
Set of 4 slightly uprated lowered springs for 750 and 101 series Sprint and Spider. Lowers the car by approximately 35 to 40 mm. Ideal for road use.
Set of 4 rubber and metal front suspension spring seats to suit all 750 and 101 series cars. See 750-098 for similar parts for the rear suspension.
Front lower wishbone ball joint cap, to fit all 750 and 101 series cars.
Front upper wishbone ball joint cap, to fit all 750 and 101 series cars.
Standard front spring for all 750 and 101 series cars. Sold individually; however, we strongly recommend replacing springs in pairs.
Track rod end locknut - left-hand thread - to fit all 750, 101 and 105 series cars.
Track rod end locknut - right-hand thread - to fit all 750, 101 and 105 series cars.
Transform the handling of your Giulietta with this suspension kit designed by UK Giulietta expert Chris Robinson. Considerably reduces body roll and improves cornering without compromising ride...
Track rod end kit for all 750 and 101 cars.
Track rod end kit for all 750 and 101 cars.
Pair of uprated Superflex anti-roll bar bushes to fit the 1" front anti-roll bar used in our 750/101 series handling kits available under our code 750-095. Also included in the kit when you order one.
Inner track rod end - left-hand thread. One used per car on the centre drag link. Lemforder was original equipment on 105 series cars and is the best quality available. Note that this track rod...
Inner track rod end - right-hand thread. One used per car on the centre drag link. Lemforder was original equipment on 105 series cars and is the best quality available. Note that this track rod...
Inner track rod end - left-hand thread. Fits the central steering drag link - one left-hand and one right-hand thread track rod end per 105 series car. Note that they also fit all 750 and 101...
54 mm exhaust clamp for standard-diameter exhaust systems on 750, 101 and 105 series cars. Usually one per car, at the joint between the front and middle exhaust sections.
Exhaust manifold to downpipe gasket to fit 3-bolt flanges on 750 series engines, 101 series 1600 Spider Veloce and Sprint Speciales. Two required per car. Should also suit cars with single-downpipe...
4-bolt exhaust gasket to fit the joint between the manifold and the downpipe on 750 series and early 101 series cars.
Cylinder head to exhaust manifold gasket for 750 series 1300 engines. 4 required per engine.
Bracket linking the gearbox mounting to the exhaust hanger, for 750 and 101 series cars.Please check your version before ordering: this part does not fit Veloce and Berlina models.
34 mm exhaust/inlet manifold stud to fit all 101, 105, 116 and 75 4-cylinder engines, including TS. There are 8 on the exhaust side and 7 on the inlet side, three of which are longer and not...
Exhaust manifold nut for 101, 105, 116 and 75 engines, including V6. 8 fitted per cylinder head. These have a smaller outside diameter than the original, which makes tightening easier as you have...
Premium-quality complete ANSA exhaust system to fit 101 series Spider Normale with 6-bolt flange.
2-into-1 exhaust section (manifold and front silencer) for the Alfa Romeo Giulia 1600 of the 101 series, in Spider Veloce and Sprint Speciale (SS) versions. The inlet diameter is 45 mm. The part...
Centre silencer and rear exhaust silencer assembly, made as a single unit. It suits all Alfa Romeo Spider models of the 750 and 101 series.
2-into-1 exhaust section (manifold and front silencer) for Alfa Romeo 750 and 101 series 1300 cc cars. Giulietta or Giulia Spider Veloce Giulietta Sprint Veloce Giulietta Sprint Speciale (SS)...
4-into-2 exhaust manifold for Alfa Romeo Giulia 1600 of the 101 series, in Spider Veloce and Sprint Speciale (SS) versions. The outlet diameter is 45 mm. This manifold is fitted with the 2-into-1...
4-into-2 exhaust manifold for Alfa Romeo 750 and 101 series 1300 cc cars. Giulietta or Giulia Spider Veloce Giulietta Sprint Veloce Giulietta Sprint Speciale (SS) Giulietta Sprint Zagato (SZ) The...
2-into-1 front exhaust silencer for Alfa Romeo Giulietta and Giulia Spider and Sprint of the 750 and 101 series, 1300 and 1600 cc. Not suitable for Veloce versions. It connects to the "short"...
2-into-1 front exhaust silencer for the early 750 and 101 series 1300 cc cars. It connects to the "short" manifolds by a single 4-hole flange.
Single-flange front silencer (3-hole flange) for Alfa Romeo Giulietta of the 750 series, 1300 cc engine. It fits in particular the Giulietta Sprint 1.3, Spider, Saloon and TI.
Inner fuel union seal to fit all Weber DCOE carburettors. This seal sits between the union and the carburettor body.
Genuine Weber top jet cover to fit all Weber DCOE carburettors. See item code FL071/1 for the matching cover gaskets.
New gasket for the top jet cover on all Weber DCOE carburettors.
Rubber seal to fit the original bayonet fuel filler caps on 750, 101 and 105 series cars. Dimensions: outside diameter 57 mm and inside diameter 39 mm.